- Messages
- 293
- Reaction score
- 422
- Points
- 213
- Location
- Byfleet
- First Name
- Jim
- Elgrand
- E51
- Region
- South East
What everyone has said, both! If I had to choose, I’d keep the grey and white one.
-
Welcome to the ElgrandOC forum. You will find that the majority of the forum is locked, but do not worry. You can unlock more content by registering to the forum completely free. Sign up is automatic, does not require email confirmation and is instant. Feel free to browse through the sections to see what topics have been covered before you register. You can register for an account by CLICKING HERE Once you have registered, you will unlock more of the forum content. You will not unlock all of the content until you have reached 10 posts. This is to give you an opportunity to chat to existing members and help to integrate you into the forum community. We are a friendly and helpful community and there is a wealth of infomation contained within the forum. Please feel free to register, introduce yourself and get to know your fellow members. Feel free to look at the Frequently Asked Questions section, the Meets/Events section and the Competition Section without having to register. We look forward to getting to know you and help you with any questions or problemd you have with your Elgrand.
What have you done to your Elgrand today?
- Thread starter Madfish
- Start date
- Messages
- 293
- Reaction score
- 422
- Points
- 213
- Location
- Byfleet
- First Name
- Jim
- Elgrand
- E51
- Region
- South East
Rubs thighs in an inappropriate manner.
Very nice! What size buddy?
- Messages
- 15
- Reaction score
- 30
- Points
- 73
- Location
- South Wales
- First Name
- Liam
- Elgrand
- E51
- Region
- Wales
Have camshaft sensors to do, shes stuck on the drive at the minute! Will be a long weekend!
- Messages
- 15
- Reaction score
- 30
- Points
- 73
- Location
- South Wales
- First Name
- Liam
- Elgrand
- E51
- Region
- Wales
hell yeah, beauties!
- Messages
- 293
- Reaction score
- 422
- Points
- 213
- Location
- Byfleet
- First Name
- Jim
- Elgrand
- E51
- Region
- South East
Thanks mate, 16” opted for comfort over phwoar factor size.
- Messages
- 11
- Reaction score
- 35
- Points
- 23
- Location
- Australia
- First Name
- Ngoc
- Elgrand
- E52
- Region
- Rest Of World
install new android screen to help with map and music and call instead of outdated stock e52 screen. Much better now as it has 2 cameras attached to the screen so I can have one dash cam and one internal cam automatically recorded when turn the car on
- Messages
- 11
- Reaction score
- 35
- Points
- 23
- Location
- Australia
- First Name
- Ngoc
- Elgrand
- E52
- Region
- Rest Of World
thanks mate I connected my phone to the car now, just thought it could only use hand free calls. However now I could connect to play music via bluetooth which is amazing !
- Messages
- 13,379
- Reaction score
- 40,424
- Points
- 473
- Location
- Normandie
- First Name
- André
- Elgrand
- E51
- Region
- Rest Of World
Gave it a wash today and continued my conversion to space shuttle.
Added a tailgate release button where the aux inputs used to be.
More buttons will follow.
Added a tailgate release button where the aux inputs used to be.
More buttons will follow.
- Messages
- 7,529
- Reaction score
- 30,100
- Points
- 478
- Location
- south yorkshire
- First Name
- Dave
- Elgrand
- E51
- Region
- Yorkshire
Like it.
Why oh why can’t I keep my bus that clean inside ( need to sell the kids)
Why oh why can’t I keep my bus that clean inside ( need to sell the kids)
- Messages
- 501
- Reaction score
- 1,228
- Points
- 213
- Location
- Sheffield
- First Name
- Phill
- Elgrand
- E51
- Region
- Yorkshire
The kids are worthless Dave, if you had dogs then maybe you’d get something but you’d never sell the dogs!
- Messages
- 696
- Reaction score
- 1,950
- Points
- 213
- Location
- North Lincolnshire
- First Name
- Brian
- Elgrand
- E51
I think I secretly wanted a white one!
- Messages
- 696
- Reaction score
- 1,950
- Points
- 213
- Location
- North Lincolnshire
- First Name
- Brian
- Elgrand
- E51
The elusive gold!
- Messages
- 696
- Reaction score
- 1,950
- Points
- 213
- Location
- North Lincolnshire
- First Name
- Brian
- Elgrand
- E51
I fitted a switch to turn off the step light, should stop some battery drain but as I understand it the bus would still think the door is open so the BCM would still take power, can better minds than mine step in if this is correct. Here is how I did it.
1 - Disconnect battery, better to be safe
2. - Remove rear side panel, probably only worth fitting switch if doing other work like door cables, like me.
3 - Take out door switch with a stubby screwdriver and remove connector, you may get connector off without but I found this easier.
4 - Cut one wire (I chose the yellow one but the switch just connects both on contact when door is open)
5- Solder both cut ends to new lengths of wire and connect to a 2 pin plug - see pic number 1.
6 - tape or use shrinksleeve to cover bare wires and poke new connector through to large hole in pillar, and re-fit door switch. See pic number 2.
7- Solder and shrink sleeve switch with corresponding connector on other end of wires.
7- Using step drill, drill a hole in plastic side cover, I did mine 70mm directly up from the seat belt hole center, this puts the switch behind the seat belt, hits the large hole in the pillar and misses any ribs in the plastic cover. Put tape on the step drill to the size you need ,I used 20mm (see pic 3) if you go too far you will need a bigger switch, No I didn't need a bigger one.
8- Put switch in hole and couple up and put cover back on, See pic 4 of finished switch.
Now with the door open the light can be turned off and the switch is in a easy place to reach from outside. This was the nearside panel, looking at LeStempy's post earlier (34915) with the little bit of wiring he has done
there is a corresponding hole in the offside pillar.
1 - Disconnect battery, better to be safe
2. - Remove rear side panel, probably only worth fitting switch if doing other work like door cables, like me.
3 - Take out door switch with a stubby screwdriver and remove connector, you may get connector off without but I found this easier.
4 - Cut one wire (I chose the yellow one but the switch just connects both on contact when door is open)
5- Solder both cut ends to new lengths of wire and connect to a 2 pin plug - see pic number 1.
6 - tape or use shrinksleeve to cover bare wires and poke new connector through to large hole in pillar, and re-fit door switch. See pic number 2.
7- Solder and shrink sleeve switch with corresponding connector on other end of wires.
7- Using step drill, drill a hole in plastic side cover, I did mine 70mm directly up from the seat belt hole center, this puts the switch behind the seat belt, hits the large hole in the pillar and misses any ribs in the plastic cover. Put tape on the step drill to the size you need ,I used 20mm (see pic 3) if you go too far you will need a bigger switch, No I didn't need a bigger one.
8- Put switch in hole and couple up and put cover back on, See pic 4 of finished switch.
Now with the door open the light can be turned off and the switch is in a easy place to reach from outside. This was the nearside panel, looking at LeStempy's post earlier (34915) with the little bit of wiring he has done
there is a corresponding hole in the offside pillar.Attachments
- Messages
- 184
- Reaction score
- 640
- Points
- 193
- Location
- London
- First Name
- Mark
- Elgrand
- E51
- Region
- London
Nice. You know there is also a button near the rear view mirror to switch off footlights. Just saying as it can get overlooked (black button on black part of rear view assembly) but that’s on an S3 E51.
- Messages
- 454
- Reaction score
- 1,541
- Points
- 313
- Location
- Isle Of Wight
- First Name
- Colin
- Elgrand
- E51
- Region
- South East
the shiny beacon on the hill, post Isle Of Wight Walk...
- Messages
- 1,675
- Reaction score
- 7,440
- Points
- 333
- Location
- Dorset
- First Name
- Andy
- Elgrand
- E51
- Region
- South West
Well I got round to fit in my or pressure gauge and temperature gauge they work quite well the temperature gauges very accurate testing that with a Thermometer the pressure gauge does fluctuate up and down a few psi but they were cheap enough and easy enough to fit had to change the oil filter to a different type because it wasn’t wide enough to fit the oil adapter plate.
When I start the engine from cold it goes over 100 psi.
Once your engine is warmed up and the oil it shows around 30 psi minimum should be 14 psi so happy at that I know my oil pressure is okay.
When I start the engine from cold it goes over 100 psi.
Once your engine is warmed up and the oil it shows around 30 psi minimum should be 14 psi so happy at that I know my oil pressure is okay.
Well in a fit of preventative maintenance I decided it was time to replace the battery, went with the much recommended silver yuasa, delivered by Amazon for a smidge over £100. And I didn't have to leave the sofa to order it.
Fitting straight forward, unclipped the top left electric box, cut off the left hand side abs plastic, refitted and nice new battery.
Dose not show up well in the pics but the old battery was starting to bulge at both ends.
Fitting straight forward, unclipped the top left electric box, cut off the left hand side abs plastic, refitted and nice new battery.
Dose not show up well in the pics but the old battery was starting to bulge at both ends.
Last edited: